ASZ Rope Tensiometer
You are here: Home » Products » Tension test series » Rope tension meter » ASZ Rope Tensiometer
Share to:

ASZ Rope Tensiometer

  • 16,500.00-21,000.00

product description

1. Applicable occasions

ASZ type rope tension meter is suitable for power industry, communication industry, transportation industry, glass wall curtain decoration industry, ropeway operation industry, construction industry, playground, tunnel construction, fishery fishing and major scientific research institutes and teaching institutions, testing institutions And occasions involving the pulling force of rope and wire rope.

2. Features

1. The rope structure with tension, can be measured directly without disassembly.

2. Light weight, simple structure and convenient operation, suitable for any occasion.

3. Stable performance, high measurement accuracy, with automatic system compensation function, when the measured cable specification is the same as the dynamometer cable specification, the accuracy can reach within 2% within the rated range.

4. It has fifteen kinds of wire diameter measurement functions and a wider measurement range.

5. Scope of application: suitable for flexible, stretched cables. Such as various steel wire ropes, high-strength ropes, etc.

6. Accuracy level: 2 ~ 6% of MAX function (depending on the rope form and characteristics).

7. Rope diameter: ¢ 6 ~ ¢ 40mm.

3. Shape and structure

Picture 39.png

4. Model specifications

Modified drawing of rope tension meter parameters

5. Working principle

The determination of cable force is divided into two types: interventional and non-interventional. The so-called interventional force measurement refers to connecting a tension sensor in series at the end or span of the cable, and directly reading the cable force. This is the most accurate and intuitive force measurement method, as shown below 1, 2 shows.


Picture 41.png

The input of this force measurement method is large, and it is only suitable for experimental research and individual projects with large tonnage and high requirements. It is not suitable for prestressed structural projects with large amount of cable.

There are also two methods of non-intrusive force measurement. One is the vibration frequency measurement method, that is, the natural vibration period T of the cable is a function of the tension H, the length L of the cable, and the mass W of the cable. From the formula, the measured The cable's vibration period T can calculate the tensile force H in the cable. The principle is relatively simple, but the seismic signal is converted into a signal, and the cable force value is output after being processed by the computer. This process requires many instruments and equipment, which makes it difficult for workers to master, and is not convenient for working at heights. In addition, the supporting conditions of the cable end have an impact on the vibration period and the accuracy of the cable force measurement. Another principle for measuring the cable force is based on mechanical principles. As shown in the figure below, there is a functional relationship between the lateral displacement δ of the cable force and the tensile force H, lateral force P of the cable and the length of the cable. When the displacement maintains a certain value, the greater the cable tension H, the greater the lateral force P.

Picture 42.png

The force sensor outputs the lateral force P, which is converted into cable tension after being processed by the microprocessor, and then displayed on the LCD. The above principle is also relatively simple, but the relationship between the lateral force and the cable force is still related to the diameter of the cable, the cross-sectional structure. The elongation of the rope and the size of the tensile force, etc. We use the correction and accurate calibration of the microprocessor After getting the correct and stable cable. Can pass the test and inspection, has reached the level of similar foreign products.

Six, screen display

Picture 43.png

1. PEAK display

When \"PEAK \" is displayed, it indicates Peak mode (peak holding mode), the display shows the peak until manually cleared; when \"PEAK \" is not displayed, it means \"track mode \" (real-time load value mode) , The value on the screen changes with the load.

2. MEM display

When data is stored in memory, \"MEM \" will be displayed. When you press \"Save \" to view the memory data, \"MEM \" flashes.

3. Unit display

The letters \"K \" are combined with \"N \", \"kgf \", \"lbf \" to form \"KN (thousand of cattle) \", \"t (tons) \", \"Klb (Thousand pounds) \"As shown:

4. MAX, MIN display

When the measured value is greater than the MAX value, MAX is displayed;

When the measured value is less than the MIN value, MIN is displayed.

1. Power display

Power displayPicture 44.pngAnd low battery tips.

Seven, key introduction

Picture 45.png

1. ON / OFF key: can be used to turn on and off.

2. Setting key: the user can enter the setting menu through this key in the measurement interface, and press this key to save the data when setting the data.

3. Save key: used to save the measured data, long press this key to enter the view interface. When viewing the interface, press this key to select the currently stored measurement value.

4. Zero setting key: during real-time measurement, press this key to correct the zero point. During peak and auto peak, press this key to clear the peak and return to zero; when viewing the interface, press this key to clear the currently stored measurement value, long press this key to clear all stored measurement values. In the user setting interface, press this key to return to the previous interface without saving data.

Eight, boot display

Picture 46.png

Nine, function introduction

1. Setting function

a. Unit setting: After the start-up display is completed, press \"Settings \" to enter the unit setting, and press \"Set Zero \" once to switch between N, kg, and Ib units, and select the desired unit. , And then press \"Settings \" to enter the next function setting, as shown in the figure below:

Picture 47.png


b. Peak setting: After the previous operation is completed, press \"Settings\" to enter the peak setting, and press \"Zero \" once to perform PEAK (indicating peak hold mode), no such character display (indicating real time Load value mode) Switch between the two modes, select the desired mode, and then press \"Settings \" to enter the next function setting, as shown in the following figure:


Picture 48.png


c. Limit setting: After the previous operation is completed, press \"Settings \" to enter the lower limit setting, press \"Save \" and \"Zero \" keys to adjust the numbers and select the desired value, Press \"Settings \" again to enter the next function setting, as shown below:

Picture 49.png

d. Upper limit value setting: After the previous operation is completed, press \"Settings \" to enter the upper limit value setting, respectively press \"Save \", \"Zero \" to adjust the numbers and select the desired value , And then press \"Settings \" to enter the next function setting, as shown in the figure below:

Picture 50.png

e. Backlight function setting: After the previous operation is completed, press \"Settings \" key to enter the backlight function setting, and press \"Zero \" key once to switch between YES and NO modes, select the required Mode, then press \"Settings \" to enter the next function setting, as shown in the figure below:

Picture 51.png

f. Automatic shutdown time setting: After the previous operation is completed, press \"Settings \" to enter the automatic shutdown time setting. Press \"Save \" and \"Zero \" keys to adjust the numbers and select the desired value. , And then press \"Settings \" key to display the setting completed interface, and then return to the measurement mode, as shown in the following figure:

Picture 52.png

2. Selection of number slot

After booting, press and hold \"Save \" key to enter the gear selection, press \"Zero \" key to select the gear, and then press \"Settings \" key, the system saves the data, automatically shuts down, restarts after shutdown, as follows The picture shows:

Picture 53.png

3. Save function

a. Under the normal measurement state, press the \"Save \" key to save a measurement value obtained while testing;

b. Press and hold the\"Save\" button for 4 seconds to enter the view interface. The \"MEM \" character flashes on the interface to view the stored data. Then press the\"Save \" key to view the next set of data and press \ Press the\"Zero \" key to return to the measurement mode, as shown in the following figure:

Picture 54.png

10. How to use

1. According to the outer diameter of the tested rope, select the cable number gear. (For the specific key operation, please refer to the second point of the function introduction above)

Picture 55.png

Note: During the test, align the highest point of the rope with the positioning block, and press the tested rope tightly on the positioning block.

Loosen the locking handle, the tested rope passes between the locking block and the positioning block, the two support bases are in full contact with the rope, as shown in the figure below, press \"Zero \" to select the measurement mode (real-time load value mode Peak hold mode, peak hold automatic release mode).

Picture 56.png

2. Tighten the locking handle and press the tested rope against the positioning block. The displayed value is the actual tension of the tested rope.

11. Safety Precautions

Precautions

Incorrect operation may damage the instrument or cause serious accidents. This manual points out important matters for preventing accidents and how to use the instrument. Please read this manual carefully before use, and keep it properly after reading, so that you can read it again.

If you are testing the impact load, please select the model whose MAX load is twice the impact load to be tested.

Warning matters

1. Do not use the instrument beyond the MAX range. Otherwise, the sensor may be damaged or even an accident may occur.

2. When the test value exceeds the range, the buzzer will beep continuously, at this time, please quickly release the added load or reduce the load.

Safety Precautions

1. Please use the matching charger to charge, otherwise it will cause circuit failure and even fire.

2. Do not use a power supply other than the rated voltage of the charger, otherwise it may cause electric shock or fire.

3. Do not pull out or insert the plug with wet hands, otherwise it may cause electric shock.

4. Do not pull the plug of the charger's power cord to pull out the plug, so as to prevent the cord from being broken and being shocked.

5. Please clean the machine with a soft cloth. Immerse the cloth in water soaked with detergent and wring it out to remove dust and dirt.

Note: Do not use volatile chemicals to clean the machine (such as volatile agent, thinner, alcohol, etc.)

6. Do not operate the machine in the following environment

(1) Humid environment (2) Dusty environment

(3) Places where oil or chemicals are used (4) Places with vibrators around

7. Please use and store within the specified temperature and humidity range, otherwise it may cause instrument failure.

8. Do not dismantle, repair or modify the machine by yourself, these actions may cause instrument failure.

9. Other matters that need to be paid attention to in safety production.

Other supporting instruments

equipment name

model

equipment name

model

Digital push-pull force gauge

HF

Electric vertical machine

AEV

Pointer push-pull force gauge

NK

Electric single column vertical machine

AEL

Digital torque tester

ANL

Electric horizontal machine

AEH

Bottle Cap Torque Tester

ANL-P

Spiral side roll test machine

ASC

Pointer torque screwdriver

ANQ

Manual horizontal test stand

AMH

High-speed impact torque tester

AGN

Manual vertical and horizontal test stand

ASL

Dynamic torque tester

AND

Hand-pressed tensile and compression test stand

AST

Torque wrench tester

ANJ

Spiral tension and compression test stand

ALX

Torsion spring testing machine

ANH

Special testing machine for peeling force

ABL

Spring tension and compression testing machine

ATH

Ball pressure test device

AQY

Shore Rubber Hardness Tester

LX

Motorized hydraulic tension and compression test stand

ALR

Shore Hardness Test Stand

LAC-J

Button Tester

ABQ

Fruit Hardness Tester

AGY

Terminal tensile tester

ADL

Fruit Hardness Tester Stand

GYJ

Rope tension meter

ASZ

Tonometer

ATN

Side pressure tension tester

HD

产品表单
Want to know more, contact us further!

Subscription information

Send your email to get more latest product information.

订阅

Quick Links

contact us

our address

Zhiguang Industrial Zone, Liushi Town, Yueqing City, Wenzhou City, Zhejiang Province

No.63 Liule Road, Liushi Town, Yueqing City, Wenzhou City, Zhejiang Province


phone

0577-57151532

0577-57572513 0577- 57575950


e-mail

ruby@tripodinstrument.com